spsemi rev 2017 01 06 ... www.spsemi.cn page 1 of 4 surface mount transient voltage suppressor stand-off voltage - 6.0 to 60 volts 2000 watt peak pulse power features for surface mounted applications in order to optimize board space low profile package built-in strain relief glass passivated junction low inductance excellent clamping capability repetition rate (duty cycle):0.01% fast response time: typically less than 1.0ps from 0 volts to v(br) for unidirectional types typical ir less than 2a above 10v high temperature solderting: 260c/10 seconds at terminals plastic package has underwriters laboratory flammability 94v-o pb-free plated tecd(2000w) series mechanical data devices for bipolar application for bidirectional use c or ca suffix for types tecd6.0 thru types tecd60 (e.g. tecd6.0c , tecd60ca) electrical characteristics apply in both directions maximum ratings and characteristics ratings at 25 ambient temperature unless otherwise specified. notes : 1.non-repetitive current pulse , per fig. 3 and derated above ta = 25 per fig. 2 . 2.mounted on 8.0mm x 8.0mm copper pads to each terminal 3.8.3ms single half sine-wave , or equivalent square wave, duty cycle = 4 pulses per minutes maximum. peak pulse power dissipation on 10/1000s waveform (note 1,2 ,fig.1) peak pulse current of on 10/1000s waveform (note 1,fig.3) peak forward surge current,8.3ms single half sine-wave superimposed on rated load,(jedec method) (note2,3) operating junction and storage temperature range rating symbol value units p ppm i ppm i fsm t,t jstg minimum 2000 see table 1 - 55 to +150 300 watts amps amps case: jedec do-214ab. molded plastic over glass passivated junction terminals: solderable per mil-std-750,method 2026 polarity: color band denoted positive end (cathode) except bidirectional 16mm tape (eia std rs-481) standard packaging: 0.007ounce,0.21gram weight:
spsemi dimensions (do-214ab) electrical characteristics table1 0.126 3.20 () 0.112 2.85 () 0.280(7.11) 0.260(6.60) 0.245(6.22) 0.220(5.60) cathode band 0.118(3.00) 0.081(2.06) 0.329 8.35 () 0.305 7.75 () 0.069 1.75 () 0.059 1.50 () 0.067 1.70 () 0.030 0.76 () do-214ab(smc j-bend) dimensions in inches and(millimeters) tecd(2000w) series tecd6.0a tecd8.0a tecd12a tecd15a tecd16a tecd20a tecd22a tecd26a tecd28a tecd30a tecd33a tecd36a tecd40a TECD58A tecd60a tecd part number device marking code reverse stand-off voltage v (v) rwm v (v)min. br v (v)max. br te s t current it(ma) maximum clamping voltage @ipp vc(v) peak pulse current ipp(a) reverse leakage @v rwm i(a) r
spsemi characteristic curves (ta=25 unless otherwise noted) fig.1 peak pulse power rating fig.2 pulse derating cruve fig.3 pulse waveform fig.4 typical junction capacitance 0 0 1.0 2.0 4.0 3.0 10/1000 sec waveform . s.. ss s s s . .. . s s . s s s . ss. . s s . s s . s s s . . .s . . . . . s ss . s .ss s ... .ss.
spsemi marking code tape and reel specification recommended soldering conditions recommended conditions reflow soldering t s t p t l time 25 time to peak temperature (t 25 to peak) temperature t (min) s t (max) s t l t p preheat ramp-down ramp-up critical zone ttot lp re?ow condition pb-free assembly (see fig.1) pre heat -temperature min(t ) s(min) -temperature max(t ) s(max) -time(min to max)(t ) s average ramp up rate (liquidus temp(t ) to peak) l t to t -ramp-up rate s(max) l re?ow -temperature(t )(liquidus) l -temperature(t ) l peak temp(t ) p time within 5 of actual peak temp(t ) p ramp-down rate time 25 to peak temp(t ) p do not exceed +150 +200 60-180secs 3 /sec.max. 3 /sec.max. +217 60-150secs +260(+0/-5) 30 secs.max. 6 /sec.max. 8 min.max. +260 cathode band 6 k **** marking code logo date code 6 l **** marking code logo date code 0.157 (4.0) 0.63 (16.0) 0.315 (8.0) 0.65 (16.4) symbol ea per reel reel dia (mm) industry standard tecd*** 500 178 eia rs-481 7 0(178) . tecd(2000w) series rev 2017 01 06 ... www.spsemi.cn page 4 of 4
|
